General Boat Fittings

Brass catch -spring loaded.

Continuous length 304 grade stainless steel hinge. Can then be cut to size. 4mm countersunk holes drilled. Offset holes drilled 51mm apart.

Materials:Impact resistant, U.V. stabilised Nylon FeaturesLength x Width 47 x 15mmWidth: 15.0mmLength: 47.0mmWeight: 8g

Stainless steel toggle latch. This latch is adjustable and lockable. 90mm x 35mm

Standard flat mount.Lever action with an eye for a padlock. ‚ Bolt down area size - 70mm x 33mmTotal length - 90mm

The double hinge design significantly reduces rattle over conventional cabin hooks. ‚ Dimensions: Base size: 42x26mm Length: 100mm Depth: 20mm Mou...

Sheaves have a deep groove to cradle 5mm (3/16") diam. wire. ‚ Applications: Ideal for small runabouts where hydraulic steering is not needed. ‚ Ma...

Sheaves have a deep groove to cradle 5mm (3/16") diam. wire. ‚  Applications: Ideal for small runabouts where hydraulic steering is not needed....

Sheaves have a deep groove to cradle 5mm (3/16") diam. wire. ‚  Applications: Ideal for small runabouts where hydraulic steering is not needed....

Sheaves have a deep groove to cradle 5mm (3/16") diam. wire. ‚  Applications: Ideal for small runabouts where hydraulic steering is not needed....

Ideal for small runabouts where hydraulic steering is not needed. Suits 5mm (3/16") diameter wire. Material: Chrome plated brass Weight: 30g

Sheaves have a deep groove to cradle 5mm (3/16") diam. wire. ‚ Applications: Ideal for small runabouts where hydraulic steering is not needed. ‚ Ma...

Ideal for small runabouts where hydraulic steering is not needed. ‚  Material: ‚  Stainless Steel ‚  Weight: 75g

Sheaves have a deep groove to cradle 5mm (3/16") diam. wire. ‚  Applications: Ideal for small runabouts where hydraulic steering is not needed....

UV resistant nylon material with a serration across the centre so it can be made into two smaller vents, if required.Choice of black or white colou...

304 grade pressed stainless steel vents with holes drilled for 4mm fastenings.Features:14 louvre227 x 127mm

304 grade pressed stainless steel vents with holes drilled for 4mm fastenings. Features:2 x 6 louvre227 x 115mm

304 grade pressed stainless steel vents with holes drilled for 4mm fastenings. Features:3 louvre 127 x 65mm

High quality Australian made ventilator made from durable UV resistant, reinforced nylon to withstand the harshest of Australian conditions.The "Se...

304 grade pressed stainless steel ventswith holes drilled for 4mm fastenings. Medium stainless steel vent. 6 louvre Size: 125 x 115mm

Small stainless steel vent. 3 louvre Size: 125 x 65mm

Maxii Clam pressed 304 grade S/S vent. Commonly used as anchor well drain covers or for covering thru-transom wiring connections. Mini: 53 x 54 x 25mm

Suits standard 2 stroke motors to approximately 25 HP. Plated steel frame with plastic end caps on all tube ends. Soft rubber hand grips. Galvanise...

Simply place in the bilge to absorb fuel and oil on the surface of bilge water. "Bilge mate" is completely non-toxic and quickly Bio-degradable whe...

Two pin quick connect, black plastic fuel line fittings. Tank end and all motor end. Fits 8mm (5/16") to 10mm ‚ (3/8") ‚ ID fuel hose. Motor/tank...

Quick connect, chrome plated brass fuel line fitting. 8mm (5/16") ID hose size ‚ Suits: Chrysler Force Most Suzuki (70HP down)

Quick connect, chrome plated brass fuel line fittings. Fits 8mm (5/16") ID fuel hose. Motor/tank connector.Suits most Suzuki

Two pin quick connect, black plastic fuel line fitting to suit Johnson and Evinrude outboards.Fits 8mm (5/16") ID fuel hose.Motor and tank connecto...

Diecast, male bayonet tank end fitting to suit 8-10mm (5/26"-3/8") ID hose. ‚ Suits: Mercury bayonet Mariner bayonet

Suits Pre 1999 Mercury, Mariner (1998 and later) and Yamaha. Grey reinforced fuel hose. UV stabilised primer bulb. Fitted with motor and tank fitt...

Grey reinforced fuel hose. UV stabilised primer bulb. 2.1m in length x 8mm ID hose.Universal - no fittings supplied.

Suits OMC. Grey reinforced fuel hose.Features: UV stabilised primer bulb. Fitted with motor and tank fittings. Size: 2.1m in length x 8mm ID hose....

Universal fuel tank adaptor made from solid brass. 1/4" NPT tapered thread and barb for 8mm (5/16") fuel hose.

Chrome brass tank adaptor. 1/4" NPT thread. ‚ Suits: Chrysler Pre 1999 Force Most Suzuki (70HP down)

Chrome plated brass tank adaptor, 1/4" NPT thread ‚ Suits:Most Suzuki (75HP up)

Diecast female bayonet tank adaptor, 1/4" NPT thread ‚ Suits: Mercury bayonet style Mariner bayinet style